Script MA-5300

Script config DSLAM Huawei tipe MA-5300 :

Login:
Password:

MA5300>enable
MA5300#config terminal

Step precaution!
MA5300(config)#hostname huawei

Step 1 Set the IP address of the inband NMS port (GE port).
Create an NMS VLAN
huawei(config)#vlan 10 standard

Add the upstream port to the VLAN
huawei(config)#interface gigabitethernet 7/1/0
huawei(config-if-gigabitethernet7/1/0)#switchport mode trunk
huawei(config-if-gigabitethernet7/1/0)#switchport trunk allowed vlan 10
huawei(config-if-gigabitethernet7/1/0)#exit
huawei(config)#interface gigabitethernet 7/1/1 // for subtend to frame 2
Enter the VLAN interface mode
huawei(config-if-gigabitethernet7/1/1)#switchport mode trunk
huawei(config-if-gigabitethernet7/1/1)#switchport trunk allowed vlan 10
huawei(config-if-gigabitethernet7/1/1)#exit
huawei(config)#interface vlanif 10

Set the IP address of the VLAN interface
huawei(config-if-vlanif10)#ip address [ip_equipment] 255.255.255.0
huawei(config-if-vlanif10)#exit

Step 2 Add a route.
huawei(config)#ip route 0.0.0.0 0.0.0.0 [ip_gateway]

Step 3 Set the SNMP parameters.
huawei(config)#snmp-agent sys-info version all
huawei(config)#snmp-agent community read public
huawei(config)#snmp-agent community write private

Step 4 Enable traps sending.
huawei(config)#snmp-agent trap enable standard

Step 5 Set the IP address of the target host for traps.
huawei(config)#snmp-agent target-host trap address [nms_server_ip] securityname private

Step 6 Set the IP address of the inband NMS as the source address for traps sending.
huawei(config)#snmp-agent trap source vlanif 10

Step 7 Save the data.
huawei(config)#write

Configure ADSL
Step 1 Registering ADEE board to MA5600 SCUB
huawei(config)#show board 0

if board still in “auto_find” state, please run command as below;
huawei(config)#board confirm 0

Step 2 Create smart VLAN for ADSL
huawei(config)#vlan 340
huawei(config-vlan 340)#vlan-type smart
huawei(config-vlan 340)#exit
huawei(config)#vlan 341 // for subtend to frame 2
huawei(config-vlan 341)#vlan-type smart
huawei(config-vlan 341)#exit

Add the upstream port to the VLAN
huawei(config)#interface gigabitethernet 7/1/0
huawei(config-if-gigabitethernet7/1/0)#svlan-upport vlan 340
huawei(config-if-gigabitethernet7/1/0)#svlan-upport vlan 341 // for subtend to frame 2
huawei(config-if-gigabitethernet7/1/0)#exit
huawei(config)#interface gigabitethernet 7/1/1
huawei(config-if-gigabitethernet7/1/1)#svlan-downport vlan 341 // for subtend to frame 2
huawei(config-if-gigabitethernet7/1/1)#exit

Enter the VLAN interface mode


Step 4 Configuring the service port bundle from GE uplink to EADA or EADB board
huawei(config)# vlan 340
huawei(config-vlan340)#svlan-downport adsl0/0/0 to adsl15/0/47 // For board slot 0-15

Step 5 Configuring ADSL line profile for subscriber
huawei(config)#adsl line-profile add 10
Command:
adsl line-profile add 10
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be neglected
>　Do you want to name the profile (y/n) [n]:
> Please choose default value type 0-adsl 1-adsl2+ (0~1) [0]:1
> Will you set basic configuration for modem? (y/n)[n]:y
Note: Setting to these mode of G992.3~5 will lead that the adsl ports that are not support adsl2+ not be activated
ADSL transmission mode:
> 0: All (G992.1~5,T1.413)
> 1: Full rate(G992.1/3/5 or T1.413)
> 2: g.lite(G992.2/4) (ADSL over ISDN board doesn't support g.lite mode)
> 3: T1.413(ADSL over ISDN board doesn't support T1.413 mode)
> 4: g.dmt (G992.1/3/5)
> 5: g.hs (G992.1~5, G992.5 is prior)
> 6: G992.1
> 7: G992.2
> 8: G992.3
> 9: G992.4
> 10:G992.5
> 11: ADSL all (G992.1~2,T1.413)
> 12: ADSL&ADSL2(G992.1/3 or T1.413)Please select (0~12) [0]:0
> Trellis mode 0-disable 1-enable (0~1) [1]:
> Downstream channel bit swap 0-disable 1-enable (0~1) [0]:
> Upstream channel bit swap 0-disable 1-enable (0~1) [0]:
> Please select channel mode 0-interleaved 1-fast (0~1) [0]:
> Will you set interleaved delay? (y/n)[n]:
>　Please select form of transmit rate adaptation in downstream:
> 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (0~2) [1]:
> Will you set SNR margin for modem? (y/n)[n]:
> Will you set parameters for rate? (y/n)[n]:y
> Minimum transmit rate in downstream (32~32000 Kbps) [32]:32 ->bukan 64
> Maximum transmit rate in downstream (1024~32000 Kbps) [24544]:384
> Minimum transmit rate in upstream (32~6000 Kbps) [32]:32
> Maximum transmit rate in upstream (32~6000 Kbps) [1024]:64
Add profile 10 successfully

huawei(config)#adsl activate adsl0/0/0 to adsl6/0/47 10
huawei(config)#adsl activate adsl9/0/0 to adsl15/0/47 10

Step 7 Configuring PITP P-mode
huawei(config)# pitp pmode enable
huawei(config)# pitp pmode enable adsl0/0/0 to adsl15/0/47 pvc all

Step 8 Saving configuration
huawei(config)#write